Buyer – Página: 89

Apollo 650 W Watt 12V AC Magnet Pma Wind Turbine Generator + Controller 6Blades

Apollo 650W AC 12V Wind Turbine + SolarWind Hybrid RX Charge Controller for Land or Marine Use Product designed in Canada Connection Overview: The Wind Generator is connected to the charge controller, which changes the Alternative Current output by the generator to Direct Current (AC to DC). Electricity generated by the wind turbine are then stored to batteries. Note: the 12V Batteries above are not included. If your home or farm is connected to the power grid, on windier days you may be able to sell excess power generated by your wind turbine to your utility. At other times when the turbine cannot generate all the power you need, you would buy power from the grid. This concept is called net metering. Even if net metering is unavailable, you might be able to reduce your power bills by using the electricity generated by wind turbines, and become less dependent on your utility. What is a SolarWind Hybrid RX Charge Controller? GreenergyStar SolarWind Hybrid RX is he most advanced charge controller in the market today. Unlike other hybrid controllers, this multipurpose device is designed to work with Southwest Windpower’s Air-X, 403, and 303 plus other 12V AC/DC turbines and solar panels. The SolarWind Hybrid RX has utilized microprocessor based control electronics, sophisticated monitoring software, high quality finned aluminum casing and an intuitive LED display design. It is designed to work with the GreenergyStar branded grid-tie inverters to send renewable energy generated by Air-X, 12V AC/DC Turbine and solar panels back to the grid in a stable, controlled and safe manner. The following list will summarize its major features: Features: Hybrid system designed to work with Southwest Windpower’s Air-X, 403, and 303 plus other 12V AC/DC turbines and 12V solar panels Compatible with GreenergyStar branded grid-tie inverters Maximum power: 1000W (rated at 27V & 37.5A) System Voltage: 12V Nominal (see input / output sections for range) Microprocessor based control electronics to control charging, outputs and dump load Dump load utilize Pulse-width modulation (PWM) switching technology to recover power during high wind periods Manual Braking switch to isolate wind turbine from the system. Intuitive LED Display to reflect system status Keeps battery in an optimum charged state Prevents overcharge and over-discharge Internal diode to prevent reverse current to solar panels or wind turbine at night High quality finned aluminum casing to protect the interior and dissipate heat Installation Reference – not to scale (No inverter, batteries, turbines and solar panels included in this listing) Input Features: Operating voltage & current on all terminals: 11.5V ~ 27V, 0A ~ 37.5A Maximum input voltage & current on all terminals: 30V , 40A Withstand voltage: 35V (anything above will damage controller) Stand-by power consumption: 0.1W AC Turbine: For 3 phase AC turbine. The 3 wires from AC turbine can be connected to the terminals in no specific order. Built in rectifier will convert AC to DC. DC Turbines can also be connected here as the rectifier accepts DC input as well. The TURBINE LED will turn Green when there is an active input source. Solar: The SOLAR LED will turn Green when there is an active input source. DC Turbine: Recommend for Air-X since this terminal has the Stay Online feature. The TURBINE LED will not turn on since the Air-X has its own (red) charging LED. The Blue CHARGE LED will turn on when there is power coming in from the inputs. Input Protection & Specification: Manual Turbine lock to force dump load to turn on Pulse Width Modulated Dump Load Stay-Online Feature to keep Air-X up and running in low battery condition Reverse Polarity Protection Night Time Reverse current protection to prevent current going into wind turbine and solar panels Over current Protection (40A Fuse) Efficiency: Maximum 98%+ Output Features: Operating output current: 37.5A Total maximum output current: 40A Maximum current on individual output: 30A Voltage tolerance: +/- 5% Maximum Output Power: 1000W (rated at 27V & 37.5A) Output starts when inputs are above 12.5V The OUTPUT A, B, C LED will turn Orange with respect to each output. Charging Features: Battery is an input and an output at the same time The CHARGE LED will turn Blue indicating battery is being charged Overcharge protection Cut off voltage: 14.7V Over-discharge protection Cut off voltage: 11.4V Recommend using deep cycle batteries if possible Normal lead acid batteries are acceptable as well 3 charging modes: Continuous charging, Pulsing, Trickiling. Power Supply Modes: Mode 1 – Power Supply When input voltages are lower than the battery’s voltage, the battery will act as a supply to all outputs. Power to all outputs will be cut when the battery has drop down to 11.4V Mode 2 – Stay Online (for Air-X only) When battery voltage is below 11.4V and input voltages is under 9V, even though all outputs will be cut, the charge controller will still send electrical pulse to the DC input terminal every 5 – 10 seconds as indicated by the pulsing Red AX SIGNAL LED. This is necessary for Air-X’s internal controller to stay on. Since the Air-X will not wake up on its own, without these pulses, even if wind starts blowing the Air-X will free spin and no power will be generated. Warning: Controller will get damaged if polarity of battery is incorrect Protection Features: Dump Load MUST be connected at all time to protect the charge controller, no dump load = no warranty Requires a minimum of 1.2Ohm 600W resistive load to be connected to the dump load terminal Dump load activates when AC Turbine is >= 27V Unlike conventional dump loads that short circuit on activation and drop outputs to zero, the SolarWind Hybrid RX utilizes Pulse-width modulation (PDM) switching technology to only dump what is necessary and conserve the rest. (refer to Figure above) Activating dump load will slow down the AC turbine and reduce voltage spikes. Over voltage protection: All outputs will be cut when input voltage is over 30V. However dump load will stay on. The DUMMY LED will turn Red when the dump load has been activated Manual Turbine Lock (Brake) Manual Turbine Lock is used to force dump load to fully turn on (ie: short circuit) Useful when it is necessary to isolate AC wind turbine from the system (ie: during installation or maintenance) Turbine lock is the red switch at the top-left corner of the Output Face (refer to Figure 1 on page 6) ” | ” – locks turbine ” 0 ” – unlocks turbine Mechanical Specifications: Operating temperature range -25’C – 85’C Weight 952g 2.1lb Dimension (L x W x H) 19.3 x 13.1 x 6.9 cm 7.5″ x 5.2″ x 2.7″ Mounting Wall Mount at base Cooling Convection cooled with fan (activate around 50’C ~ 60’C) Casing High quality finned aluminum to act as heat sink for fast heat dissipation Apollo Wind Generator Over the last few decades renewable energy has started to gain its ground. Of all the different kinds of alternative energy sources available, the use of wind power has been growing steadily. However, wind turbines that are available for homeowners in the market today are mostly designed (or copied) a decade ago and although they work, most have mechanical flaws that were neglected since their debut and there is a lot of room for improvements. With that in mind, we have redesigned a new wind turbine – the Apollo. Built-in with a stronger alternator for higher power output, Anti-vibration system to increase power efficiency, and the ability to be customized and upgraded for the future. Exploded View (No inverter, batteries, turbines and solar panels included in this listing) What is the difference in an Apollo Wind Turbine? GreenergyStar’s Apollo Wind Turbine is the most mechanically advanced generator in the market today. It features many upgrades that solves performance issues that our competitors struggle with. It is designed to work with other GreenergyStar branded products such as the SolarWind Hybrid RX charge controller and grid tie inverters to better utilize the renewable energy generated. The following list will summarize its major features: I. Performance Curves The above battery charging power curve is obtained from charging a 12V 100Ah battery bank with our SolarWind Hybrid Charge Controller. Blade Features – Color: White – With 49″ swept area when mounted on a 5″ Hub – Incorporates highly efficient, true airfoil – Quiet performance with minimal vibration – Can generate 800 watts or more depending on PMA efficiency – Manufactured using a precision injection molding process that produces blades of exceptional consistency – Made with new thermoplastic to increase durability – Smoother and more durable than any blades you can find in the market – Adjustable blade degree with included degree adjusters / shims (see picture below) – High resistance to bending (over 150 degrees) What is Nylon 6.6? Nylon is a man made product. On the man made side, you will see primarily three types of thermoplastic. These are polyester, polypropylene, and nylon. Of the three types, nylon is by far the better choice. Nylon is extremely versatile in its applications. It is highly resistant to abrasion and has excellent resilience. Within nylon, there are two groups: nylon 6 and nylon 6.6. Nylon 6.6 is the premium thermoplastic. It is the thermoplastic that is most often specified by professional architects and designers because it provides the flexural strength, low-temperature toughness, UV Resistance and is the most resilient. Nylon 6.6 performs well in many applications such as wind turbine blades, automotive parts, and other fields that get a lot of wear and tear. Nylon 6.6 has additional molecules that give extra strength and the resilience compared to nylon 6. If you still have no idea what Nylon 6.6 is, do a search on google. Adjustable blade degree with included degree adjusters (Shims) Increase/decrease blade angle by installing degree adjuster under the blades “+” on the right side = Increase angle = More Torque, Less Speed “-” on the right side = Decrease angle = Less Torque, More Speed Specification Material Nylon 6.6 + Carbon Fiber (<20%) Length 23.5 inches Width (base) 5 inches Mounting 6mm bolts Weight (per blade) 166g, 6oz Slip Ring For those who are serious about wind power generation, this is a must have item. Never again will the cable get twisted up. Never again will you have to climb up the ladder and fix the tangles. Get a slip ring today and you can put all of that behind you. Slip Ring Specification: Circuits 3 Voltage 380VAC/DC Maximum Current 60A X3 Rated Current 40A X3 Working Speed 250RPM Temperature -40'C to 100'C Wire Gauge 6AWG Number of bearings 2 Thread M22x1.5 22mm diameter 1.5mm Thread Pitch Features: – High voltage / current carrying capacity – Copper-graphite brushes ensure long life even under extreme load conditions – Quick connector for fast connection to the AC / DC wind turbine *see reference picture below* – Insulated with fiberglass sleeves to protect wires to the wind turbine and make the installation professional and tidy – Easily taken apart for quick maintenance – 2x High Quality Metal Sealed Ball bearing to stabilize axle Exploded View Connection Overview As we can see from the exploded view, the top circuit is color coded Red, the middle circuit is Black and the bottom circuit is Blue. Rotor Apollo Competitor's Pros – 20mm rotor thickness, 66% more compare to competitor's – Stronger Magnetic flux due to thicker rotor, and thus, more Power – Evenly spread magnets decrease magnetic drag – 6 balanced hole to reduce weight – Reduce forces required to start rotor due to less reciprocation mass – Brushless Permanent Magnet Alternator Cons – only 12mm in rotor thickness and thus weaker magnetic flux – Magnets are not evenly spread out (ie: screw at top) – No weight reduction = harder start up Specification Rotor Diameter 77mm Magnet Material Rare Earth Neodymium magnets Number of Magnets 12 Magnet Width (Rotor thickness) 20mm Weight 682g Body Reference picture ONLY. Please refer to listing details on the actual model you are getting. – Bigger body allow fitting of a more powerful alternator than competitor's – Longer body and tail (62cm) allow the Apollo to face wind even if more blades are added while our competitor just spins round and round – High surface area tail, 33cm in height, 30% more surface area will let the turbine stay focus to incoming wind – Installation of 29" blades and capture 50% more wind is now possible Specification Material Aluminum (with coating) Length 62 cm Tail Height 33 cm Tail surface Area 225 cm^2 Upgradable with 29" blades Yes Blades allowed 6 Hub Pros – 140mm diameter, 10% larger than competitor's – High blade capacity, allow up to 6 to be installed – Covers the entire face plate to eliminate vortex Cons – 125mm in diameter – Only allows 3 blades to be installed – Does not cover face plate completely Specification Material Aluminum (with coating) Diameter 140 mm Capacity 6 Blades Compatibility Air-X, 403, 303 Shaft Diameter for 17mm shaft Disc Thickness 23mm II. Anti-Vibration System Horizontal Pros – Dual Metal ball bearing located at front and rear of rotor – 5.5cm of stabilizing distance to prevent rotor and blades from vibrating – No vibration = Increase in efficiency – Reduction in noise output Cons – 2 bearings placed side by side together – Stabilizing distance effectively shorten to 2cm (63% reduction) – Vibration = Energy wasted – Wasted energy gets converted to Noise and Heat Vertical Pros – Dual Metal ball bearing to prevent vertical vibration – Yaw shaft diameter: 40mm – 3cm of stabilizing distance with 2 bearings – No vibration = Increase in efficiency – Reduction in noise output – One piece design Yaw body provides more stability Cons – Single bearings will not eliminate vertical vibration – Yaw shaft diameter: 35mm – Stabilizing distance effectively shorten to 1.4cm with one bearing (53% reduction) – Vibration will cause bearing to grind on yaw shaft and create a bigger play, which in turn will cause more vibration in a never ending cycle – 2 pieces design Yaw body is less stable III. Anti-Leak System Pros – Unlike rubber, PVC Rings are much more durable will not harden and crack and cause leaks – Bearing are covered and will not rust / leak Cons – Rubber ring will harden after approximately 1 year of use and will start cracking and leaking – Bearing are exposed and will rust / leak IV. Generator Specification Body Material Aluminum Rotor Diameter 124.5cm (49 inches) Starting Wind Speed (6 blades) 3.0m/s (7 mph) Rated Wind Speed 13m/s Survival Wind Speed 45m/s Voltage 12 VAC Rated Power 550W Maximum Power 650W Weight 8.28kg (18.25 lb) Yaw Body / Tower Mount Inner Diameter 53.3mm, 2.1 inch Recommended Tower (Pipe) Size 1.5 inch schedule 40 pipe Actual Pipe diameter: 48mm (1.9 inch) Recommend adding 2.5mm padding What are included: -1 Apollo Wind Turbine – 6x Blades – Hub with 6 lots – Nose Cone – Screws and Nuts – Degree Adjuster – Allen Key – Instruction Manual – RX Charge Controller WARNING !!! Rotating blades present the most serious mechanical hazard. The blades may be moving at velocities over 275 miles per hour (440 km/hr). At this speed, the tip of a blade is nearly invisible and can cause serious injury. Under no circumstances should you install the turbine where a person could come in contact with moving rotor blades. The installer of these blades is solely responsible for the use or misuse of these blades. We assume no liability for ANY injuries caused by these products Warranty: We will warrant this unit against any manufacture defects or workmanship for 1 year from the date of purchase. This limited warranty specifically excludes damage caused by improper installation, accident, misuse, abuse, improper storage, or any unauthorized disassembly, repair, or modification.This warranty is not transferable. In the event of a claim against this warranty, the seller's obligation, and the claimant's sole remedy, shall be replacement of the product, repair, or refund of the original purchase price excluding any shipping and handling fees. All shipping and handling fees going both ways are responsible by the buyer. NO OPERATING COST GENERATES ELECTRICITY FROM THE ABUNDANT RESOURCE – SOLAR & WIND Terms & Conditions Bidding on this auction means that you agree with the following terms & conditions. All pictures and descriptions are subjected to change without notice. Items may or may not look exactly the same as the auction shown. We are not responsible for any inadvertent errors. Payment Total payment = winning price + shipping & handling Example A: Winning price: $9.00, S&H: $1.00, then Total = US$10.00 Example B: Winning price: $1.00, S&H: $9.00, then Total = US$10.00 There will be an extra US$0.50 the Paypal penalty fees for any insufficient Paypal payments. Shipping and Handling 1. Shipping & Handling fees includes: the shipping fee itself, eBay and Paypal commissions, packaging materials, documentation and other minor fees. 2. Please refer to the shipping chart for details. 3. APO / FPO shipping is equal to International shipping. Please refer to S&H price list above for details. 4.Combine shipping is available to buyers when the following conditions are met: ALL items are paid in a SINGLE payment Items are purchased within 2 days International Buyers: Due to high shipping outside of North America, there will be no combine shipping discount when accumlated shipping fees is below US$60.00. *note: combine shipping are charged based on the highest shipping cost of the 1st item and half of the shipping for each additional items. i.e.: Item A Shipping: $5.00 Item B Shipping: $7.00 Item C Shipping: $10.00 Then total shipping will be $10.00 (item C is highest) + $3.50 (1/2 of item B) + $2.50 (1/2 of item A) = $16.00 5. Items are shipped within 48 hours after payment is confirmed. Please expect 5 to 10 business days before you receive your item(s). International bidders should expect a longer time. 6. Bounce backs due to incorrect shipping address will result in setback on deliveries. Usually it will take 45 days for bounce backs to return to us. So, PLEASE make sure you address is correct. It will be the buyer's responsibility to repay the S&H if such incident has occurred Return & Refund Policy No refunds after 30 days Shipping & handling & other service fees are NOT refundable All returned items must be in original packing. Items that are used/ damaged/ deformed or altered in any ways are not acceptable. A 20% restocking fee will be charged on all refunded items.

Apollo 650 W Watt 24 V AC (6Blades) Wind Turbine Generator Land/Marine Use

Apollo 650W AC 24V Wind Turbine for Land or Marine Use Product designed in Canada Introduction Over the last few decades renewable energy has started to gain its ground. Of all the different kinds of alternative energy sources available, the use of wind power has been growing steadily. However, wind turbines that are available for homeowners in the market today are mostly designed (or copied) a decade ago and although they work, most have mechanical flaws that were neglected since their debut and there is a lot of room for improvements. With that in mind, we have redesigned a new wind turbine – the Apollo. Built-in with a stronger alternator for higher power output, Anti-vibration system to increase power efficiency, and the ability to be customized and upgraded for the future. Exploded View (No inverter, batteries, turbines and solar panels included in this listing) What is the difference in an Apollo Wind Turbine? GreenergyStar’s Apollo Wind Turbine is the most mechanically advanced generator in the market today. It features many upgrades that solves performance issues that our competitors struggle with. It is designed to work with other GreenergyStar branded products such as the SolarWind Hybrid RX charge controller and grid tie inverters to better utilize the renewable energy generated. The following list will summarize its major features: I. Performance Curves The above battery charging power curve is obtained from charging a 24V 100Ah battery bank Blade Features – Color: White – With 49″ swept area when mounted on a 5″ Hub – Incorporates highly efficient, true airfoil – Quiet performance with minimal vibration – Can generate 800 watts or more depending on PMA efficiency – Manufactured using a precision injection molding process that produces blades of exceptional consistency – Made with new thermoplastic to increase durability – Smoother and more durable than any blades you can find in the market – Adjustable blade degree with included degree adjusters / shims (see picture below) – High resistance to bending (over 150 degrees) What is Nylon 6.6? Nylon is a man made product. On the man made side, you will see primarily three types of thermoplastic. These are polyester, polypropylene, and nylon. Of the three types, nylon is by far the better choice. Nylon is extremely versatile in its applications. It is highly resistant to abrasion and has excellent resilience. Within nylon, there are two groups: nylon 6 and nylon 6.6. Nylon 6.6 is the premium thermoplastic. It is the thermoplastic that is most often specified by professional architects and designers because it provides the flexural strength, low-temperature toughness, UV Resistance and is the most resilient. Nylon 6.6 performs well in many applications such as wind turbine blades, automotive parts, and other fields that get a lot of wear and tear. Nylon 6.6 has additional molecules that give extra strength and the resilience compared to nylon 6. If you still have no idea what Nylon 6.6 is, do a search on google. Adjustable blade degree with included degree adjusters (Shims) Increase/decrease blade angle by installing degree adjuster under the blades “+” on the right side = Increase angle = More Torque, Less Speed “-” on the right side = Decrease angle = Less Torque, More Speed Specification Material Nylon 6.6 + Carbon Fiber (<20%) Length 23.5 inches Width (base) 5 inches Mounting 6mm bolts Weight (per blade) 166g, 6oz Slip Ring For those who are serious about wind power generation, this is a must have item. Never again will the cable get twisted up. Never again will you have to climb up the ladder and fix the tangles. Get a slip ring today and you can put all of that behind you. Slip Ring Specification: Circuits 3 Voltage 380VAC/DC Maximum Current 60A X3 Rated Current 40A X3 Working Speed 250RPM Temperature -40'C to 100'C Wire Gauge 6AWG Number of bearings 2 Thread M22x1.5 22mm diameter 1.5mm Thread Pitch Features: – High voltage / current carrying capacity – Copper-graphite brushes ensure long life even under extreme load conditions – Quick connector for fast connection to the AC / DC wind turbine *see reference picture below* – Insulated with fiberglass sleeves to protect wires to the wind turbine and make the installation professional and tidy – Easily taken apart for quick maintenance – 2x High Quality Metal Sealed Ball bearing to stabilize axle Exploded View Connection Overview As we can see from the exploded view, the top circuit is color coded Red, the middle circuit is Black and the bottom circuit is Blue. Rotor Apollo Competitor's Pros – 20mm rotor thickness, 66% more compare to competitor's – Stronger Magnetic flux due to thicker rotor, and thus, more Power – Evenly spread magnets decrease magnetic drag – 6 balanced hole to reduce weight – Reduce forces required to start rotor due to less reciprocation mass – Brushless Permanent Magnet Alternator Cons – only 12mm in rotor thickness and thus weaker magnetic flux – Magnets are not evenly spread out (ie: screw at top) – No weight reduction = harder start up Specification Rotor Diameter 77mm Magnet Material Rare Earth Neodymium magnets Number of Magnets 12 Magnet Width (Rotor thickness) 20mm Weight 682g Body Reference picture ONLY. Please refer to listing details on the actual model you are getting. – Bigger body allow fitting of a more powerful alternator than competitor's – Longer body and tail (62cm) allow the Apollo to face wind even if more blades are added while our competitor just spins round and round – High surface area tail, 33cm in height, 30% more surface area will let the turbine stay focus to incoming wind – Installation of 29" blades and capture 50% more wind is now possible Specification Material Aluminum (with coating) Length 62 cm Tail Height 33 cm Tail surface Area 225 cm^2 Upgradable with 29" blades Yes Blades allowed 6 Hub Pros – 140mm diameter, 10% larger than competitor's – High blade capacity, allow up to 6 to be installed – Covers the entire face plate to eliminate vortex Cons – 125mm in diameter – Only allows 3 blades to be installed – Does not cover face plate completely Specification Material Aluminum (with coating) Diameter 140 mm Capacity 6 Blades Compatibility Air-X, 403, 303 Shaft Diameter for 17mm shaft Disc Thickness 23mm II. Anti-Vibration System Horizontal Pros – Dual Metal ball bearing located at front and rear of rotor – 5.5cm of stabilizing distance to prevent rotor and blades from vibrating – No vibration = Increase in efficiency – Reduction in noise output Cons – 2 bearings placed side by side together – Stabilizing distance effectively shorten to 2cm (63% reduction) – Vibration = Energy wasted – Wasted energy gets converted to Noise and Heat Vertical Pros – Dual Metal ball bearing to prevent vertical vibration – Yaw shaft diameter: 40mm – 3cm of stabilizing distance with 2 bearings – No vibration = Increase in efficiency – Reduction in noise output – One piece design Yaw body provides more stability Cons – Single bearings will not eliminate vertical vibration – Yaw shaft diameter: 35mm – Stabilizing distance effectively shorten to 1.4cm with one bearing (53% reduction) – Vibration will cause bearing to grind on yaw shaft and create a bigger play, which in turn will cause more vibration in a never ending cycle – 2 pieces design Yaw body is less stable III. Anti-Leak System Pros – Unlike rubber, PVC Rings are much more durable will not harden and crack and cause leaks – Bearing are covered and will not rust / leak Cons – Rubber ring will harden after approximately 1 year of use and will start cracking and leaking – Bearing are exposed and will rust / leak IV. Generator Specification Body Material Aluminum Rotor Diameter 124.5cm (49 inches) Starting Wind Speed (6 blades) 3.0m/s (7 mph) Rated Wind Speed 13m/s Survival Wind Speed 45m/s Voltage 24 VAC Rated Power 550W Maximum Power 650W Weight 8.28kg (18.25 lb) Yaw Body / Tower Mount Inner Diameter 53.3mm, 2.1 inch Recommended Tower (Pipe) Size 1.5 inch schedule 40 pipe Actual Pipe diameter: 48mm (1.9 inch) Recommend adding 2.5mm padding What are included: -1 Apollo Wind Turbine – 6x Blades – Hub with 6 lots – Nose Cone – Screws and Nuts – Degree Adjuster – Allen Key – Instruction Manual WARNING !!! Rotating blades present the most serious mechanical hazard. The blades may be moving at velocities over 275 miles per hour (440 km/hr). At this speed, the tip of a blade is nearly invisible and can cause serious injury. Under no circumstances should you install the turbine where a person could come in contact with moving rotor blades. The installer of these blades is solely responsible for the use or misuse of these blades. We assume no liability for ANY injuries caused by these products Warranty: We will warrant this unit against any manufacture defects or workmanship for 1 year from the date of purchase. This limited warranty specifically excludes damage caused by improper installation, accident, misuse, abuse, improper storage, or any unauthorized disassembly, repair, or modification.This warranty is not transferable. In the event of a claim against this warranty, the seller's obligation, and the claimant's sole remedy, shall be replacement of the product, repair, or refund of the original purchase price excluding any shipping and handling fees. All shipping and handling fees going both ways are responsible by the buyer. NO OPERATING COST GENERATES ELECTRICITY FROM THE ABUNDANT RESOURCE – SOLAR & WIND Terms & Conditions Bidding on this auction means that you agree with the following terms & conditions. All pictures and descriptions are subjected to change without notice. Items may or may not look exactly the same as the auction shown. We are not responsible for any inadvertent errors. Payment Total payment = winning price + shipping & handling Example A: Winning price: $9.00, S&H: $1.00, then Total = US$10.00 Example B: Winning price: $1.00, S&H: $9.00, then Total = US$10.00 There will be an extra US$0.50 the Paypal penalty fees for any insufficient Paypal payments. Shipping and Handling 1. Shipping & Handling fees includes: the shipping fee itself, eBay and Paypal commissions, packaging materials, documentation and other minor fees. 2. Please refer to the shipping chart for details. 3. APO / FPO shipping is equal to International shipping. Please refer to S&H price list above for details. 4.Combine shipping is available to buyers when the following conditions are met: ALL items are paid in a SINGLE payment Items are purchased within 2 days International Buyers: Due to high shipping outside of North America, there will be no combine shipping discount when accumlated shipping fees is below US$60.00. *note: combine shipping are charged based on the highest shipping cost of the 1st item and half of the shipping for each additional items. i.e.: Item A Shipping: $5.00 Item B Shipping: $7.00 Item C Shipping: $10.00 Then total shipping will be $10.00 (item C is highest) + $3.50 (1/2 of item B) + $2.50 (1/2 of item A) = $16.00 5. Items are shipped within 48 hours after payment is confirmed. Please expect 5 to 10 business days before you receive your item(s). International bidders should expect a longer time. 6. Bounce backs due to incorrect shipping address will result in setback on deliveries. Usually it will take 45 days for bounce backs to return to us. So, PLEASE make sure you address is correct. It will be the buyer's responsibility to repay the S&H if such incident has occurred Return & Refund Policy No refunds after 30 days Shipping & handling & other service fees are NOT refundable All returned items must be in original packing. Items that are used/ damaged/ deformed or altered in any ways are not acceptable. A 20% restocking fee will be charged on all refunded items.

Apollo 650 W Watt 24 V DC (6Blades) Wind Turbine Generator Land/Marine Use

Apollo 650W DC 24V Wind Turbine for Land or Marine Use Product designed in Canada Three Phase Bridge Rectifier Introduction Over the last few decades renewable energy has started to gain its ground. Of all the different kinds of alternative energy sources available, the use of wind power has been growing steadily. However, wind turbines that are available for homeowners in the market today are mostly designed (or copied) a decade ago and although they work, most have mechanical flaws that were neglected since their debut and there is a lot of room for improvements. With that in mind, we have redesigned a new wind turbine – the Apollo. Built-in with a stronger alternator for higher power output, Anti-vibration system to increase power efficiency, and the ability to be customized and upgraded for the future. Exploded View (No inverter, batteries, turbines and solar panels included in this listing) What is the difference in an Apollo Wind Turbine? GreenergyStar’s Apollo Wind Turbine is the most mechanically advanced generator in the market today. It features many upgrades that solves performance issues that our competitors struggle with. It is designed to work with other GreenergyStar branded products such as the SolarWind Hybrid RX charge controller and grid tie inverters to better utilize the renewable energy generated. The following list will summarize its major features: I. Performance Curves The above battery charging power curve is obtained from charging a 24V 100Ah battery bank Blade Features – Color: White – With 49″ swept area when mounted on a 5″ Hub – Incorporates highly efficient, true airfoil – Quiet performance with minimal vibration – Can generate 800 watts or more depending on PMA efficiency – Manufactured using a precision injection molding process that produces blades of exceptional consistency – Made with new thermoplastic to increase durability – Smoother and more durable than any blades you can find in the market – Adjustable blade degree with included degree adjusters / shims (see picture below) – High resistance to bending (over 150 degrees) What is Nylon 6.6? Nylon is a man made product. On the man made side, you will see primarily three types of thermoplastic. These are polyester, polypropylene, and nylon. Of the three types, nylon is by far the better choice. Nylon is extremely versatile in its applications. It is highly resistant to abrasion and has excellent resilience. Within nylon, there are two groups: nylon 6 and nylon 6.6. Nylon 6.6 is the premium thermoplastic. It is the thermoplastic that is most often specified by professional architects and designers because it provides the flexural strength, low-temperature toughness, UV Resistance and is the most resilient. Nylon 6.6 performs well in many applications such as wind turbine blades, automotive parts, and other fields that get a lot of wear and tear. Nylon 6.6 has additional molecules that give extra strength and the resilience compared to nylon 6. If you still have no idea what Nylon 6.6 is, do a search on google. Adjustable blade degree with included degree adjusters (Shims) Increase/decrease blade angle by installing degree adjuster under the blades “+” on the right side = Increase angle = More Torque, Less Speed “-” on the right side = Decrease angle = Less Torque, More Speed Specification Material Nylon 6.6 + Carbon Fiber (<20%) Length 23.5 inches Width (base) 5 inches Mounting 6mm bolts Weight (per blade) 166g, 6oz Slip Ring For those who are serious about wind power generation, this is a must have item. Never again will the cable get twisted up. Never again will you have to climb up the ladder and fix the tangles. Get a slip ring today and you can put all of that behind you. Slip Ring Specification: Circuits 3 Voltage 380VAC/DC Maximum Current 60A X3 Rated Current 40A X3 Working Speed 250RPM Temperature -40'C to 100'C Wire Gauge 6AWG Number of bearings 2 Thread M22x1.5 22mm diameter 1.5mm Thread Pitch Features: – High voltage / current carrying capacity – Copper-graphite brushes ensure long life even under extreme load conditions – Quick connector for fast connection to the AC / DC wind turbine *see reference picture below* – Insulated with fiberglass sleeves to protect wires to the wind turbine and make the installation professional and tidy – Easily taken apart for quick maintenance – 2x High Quality Metal Sealed Ball bearing to stabilize axle Exploded View Connection Overview As we can see from the exploded view, the top circuit is color coded Red, the middle circuit is Black and the bottom circuit is Blue. Rotor Apollo Competitor's Pros – 20mm rotor thickness, 66% more compare to competitor's – Stronger Magnetic flux due to thicker rotor, and thus, more Power – Evenly spread magnets decrease magnetic drag – 6 balanced hole to reduce weight – Reduce forces required to start rotor due to less reciprocation mass – Brushless Permanent Magnet Alternator Cons – only 12mm in rotor thickness and thus weaker magnetic flux – Magnets are not evenly spread out (ie: screw at top) – No weight reduction = harder start up Specification Rotor Diameter 77mm Magnet Material Rare Earth Neodymium magnets Number of Magnets 12 Magnet Width (Rotor thickness) 20mm Weight 682g Body Reference picture ONLY. Please refer to listing details on the actual model you are getting. – Bigger body allow fitting of a more powerful alternator than competitor's – Longer body and tail (62cm) allow the Apollo to face wind even if more blades are added while our competitor just spins round and round – High surface area tail, 33cm in height, 30% more surface area will let the turbine stay focus to incoming wind – Installation of 29" blades and capture 50% more wind is now possible Specification Material Aluminum (with coating) Length 62 cm Tail Height 33 cm Tail surface Area 225 cm^2 Upgradable with 29" blades Yes Blades allowed 6 Hub Pros – 140mm diameter, 10% larger than competitor's – High blade capacity, allow up to 6 to be installed – Covers the entire face plate to eliminate vortex Cons – 125mm in diameter – Only allows 3 blades to be installed – Does not cover face plate completely Specification Material Aluminum (with coating) Diameter 140 mm Capacity 6 Blades Compatibility Air-X, 403, 303 Shaft Diameter for 17mm shaft Disc Thickness 23mm II. Anti-Vibration System Horizontal Pros – Dual Metal ball bearing located at front and rear of rotor – 5.5cm of stabilizing distance to prevent rotor and blades from vibrating – No vibration = Increase in efficiency – Reduction in noise output Cons – 2 bearings placed side by side together – Stabilizing distance effectively shorten to 2cm (63% reduction) – Vibration = Energy wasted – Wasted energy gets converted to Noise and Heat Vertical Pros – Dual Metal ball bearing to prevent vertical vibration – Yaw shaft diameter: 40mm – 3cm of stabilizing distance with 2 bearings – No vibration = Increase in efficiency – Reduction in noise output – One piece design Yaw body provides more stability Cons – Single bearings will not eliminate vertical vibration – Yaw shaft diameter: 35mm – Stabilizing distance effectively shorten to 1.4cm with one bearing (53% reduction) – Vibration will cause bearing to grind on yaw shaft and create a bigger play, which in turn will cause more vibration in a never ending cycle – 2 pieces design Yaw body is less stable III. Anti-Leak System Pros – Unlike rubber, PVC Rings are much more durable will not harden and crack and cause leaks – Bearing are covered and will not rust / leak Cons – Rubber ring will harden after approximately 1 year of use and will start cracking and leaking – Bearing are exposed and will rust / leak IV. Generator Specification Body Material Aluminum Rotor Diameter 124.5cm (49 inches) Starting Wind Speed (6 blades) 3.0m/s (7 mph) Rated Wind Speed 13m/s Survival Wind Speed 45m/s Voltage 24 VDC Rated Power 550W Maximum Power 650W Weight 8.28kg (18.25 lb) Yaw Body / Tower Mount Inner Diameter 53.3mm, 2.1 inch Recommended Tower (Pipe) Size 1.5 inch schedule 40 pipe Actual Pipe diameter: 48mm (1.9 inch) Recommend adding 2.5mm padding What are included: -1 Apollo Wind Turbine – 6x Blades – Hub with 6 lots – Nose Cone – Screws and Nuts – Degree Adjuster – Allen Key – Instruction Manual WARNING !!! Rotating blades present the most serious mechanical hazard. The blades may be moving at velocities over 275 miles per hour (440 km/hr). At this speed, the tip of a blade is nearly invisible and can cause serious injury. Under no circumstances should you install the turbine where a person could come in contact with moving rotor blades. The installer of these blades is solely responsible for the use or misuse of these blades. We assume no liability for ANY injuries caused by these products Warranty: We will warrant this unit against any manufacture defects or workmanship for 1 year from the date of purchase. This limited warranty specifically excludes damage caused by improper installation, accident, misuse, abuse, improper storage, or any unauthorized disassembly, repair, or modification.This warranty is not transferable. In the event of a claim against this warranty, the seller's obligation, and the claimant's sole remedy, shall be replacement of the product, repair, or refund of the original purchase price excluding any shipping and handling fees. All shipping and handling fees going both ways are responsible by the buyer. NO OPERATING COST GENERATES ELECTRICITY FROM THE ABUNDANT RESOURCE – SOLAR & WIND Terms & Conditions Bidding on this auction means that you agree with the following terms & conditions. All pictures and descriptions are subjected to change without notice. Items may or may not look exactly the same as the auction shown. We are not responsible for any inadvertent errors. Payment Total payment = winning price + shipping & handling Example A: Winning price: $9.00, S&H: $1.00, then Total = US$10.00 Example B: Winning price: $1.00, S&H: $9.00, then Total = US$10.00 There will be an extra US$0.50 the Paypal penalty fees for any insufficient Paypal payments. Shipping and Handling 1. Shipping & Handling fees includes: the shipping fee itself, eBay and Paypal commissions, packaging materials, documentation and other minor fees. 2. Please refer to the shipping chart for details. 3. APO / FPO shipping is equal to International shipping. Please refer to S&H price list above for details. 4.Combine shipping is available to buyers when the following conditions are met: ALL items are paid in a SINGLE payment Items are purchased within 2 days International Buyers: Due to high shipping outside of North America, there will be no combine shipping discount when accumlated shipping fees is below US$60.00. *note: combine shipping are charged based on the highest shipping cost of the 1st item and half of the shipping for each additional items. i.e.: Item A Shipping: $5.00 Item B Shipping: $7.00 Item C Shipping: $10.00 Then total shipping will be $10.00 (item C is highest) + $3.50 (1/2 of item B) + $2.50 (1/2 of item A) = $16.00 5. Items are shipped within 48 hours after payment is confirmed. Please expect 5 to 10 business days before you receive your item(s). International bidders should expect a longer time. 6. Bounce backs due to incorrect shipping address will result in setback on deliveries. Usually it will take 45 days for bounce backs to return to us. So, PLEASE make sure you address is correct. It will be the buyer's responsibility to repay the S&H if such incident has occurred Return & Refund Policy No refunds after 30 days Shipping & handling & other service fees are NOT refundable All returned items must be in original packing. Items that are used/ damaged/ deformed or altered in any ways are not acceptable. A 20% restocking fee will be charged on all refunded items.

400 550 650 800 1000 W Watt 12/24 V 3/6 Blades Wind Turbine Generator+Controller

Wind Generator Please choose one Wind Generator from the model menu Below are Details for each model: Apollo 550W 12V DC ( 3 Blades) Wind Turbine for Land or Marine Use Product designed in Canada Introduction Over the last few decades renewable energy has started to gain its ground. Of all the different kinds of alternative energy sources available, the use of wind power has been growing steadily. However, wind turbines that are available for homeowners in the market today are mostly designed (or copied) a decade ago and although they work, most have mechanical flaws that were neglected since their debut and there is a lot of room for improvements. With that in mind, we have redesigned a new wind turbine – the Apollo. Built-in with a stronger alternator for higher power output, Anti-vibration system to increase power efficiency, and the ability to be customized and upgraded for the future. Exploded View (No inverter, batteries, turbines and solar panels included in this listing) What is the difference in an Apollo Wind Turbine? GreenergyStar’s Apollo Wind Turbine is the most mechanically advanced generator in the market today. It features many upgrades that solves performance issues that our competitors struggle with. It is designed to work with other GreenergyStar branded products such as the SolarWind Hybrid RX charge controller and grid tie inverters to better utilize the renewable energy generated. The following list will summarize its major features: I. Performance Curves The above battery charging power curve is obtained from charging a 12V 100Ah battery bank with our SolarWind Hybrid Charge Controller (not included in this listing) Installation Reference – not to scale – for reference only (Inverters, batteries, controller, solar panels are not included in this listing. ) Blade Features – Color: White – With 49″ swept area when mounted on a 5″ Hub – Incorporates highly efficient, true airfoil – Quiet performance with minimal vibration – Can generate 800 watts or more depending on PMA efficiency – Manufactured using a precision injection molding process that produces blades of exceptional consistency – Made with new thermoplastic to increase durability – Smoother and more durable than any blades you can find in the market – Adjustable blade degree with included degree adjusters / shims (see picture below) – High resistance to bending (over 150 degrees) What is Nylon 6.6? Nylon is a man made product. On the man made side, you will see primarily three types of thermoplastic. These are polyester, polypropylene, and nylon. Of the three types, nylon is by far the better choice. Nylon is extremely versatile in its applications. It is highly resistant to abrasion and has excellent resilience. Within nylon, there are two groups: nylon 6 and nylon 6.6. Nylon 6.6 is the premium thermoplastic. It is the thermoplastic that is most often specified by professional architects and designers because it provides the flexural strength, low-temperature toughness, UV Resistance and is the most resilient. Nylon 6.6 performs well in many applications such as wind turbine blades, automotive parts, and other fields that get a lot of wear and tear. Nylon 6.6 has additional molecules that give extra strength and the resilience compared to nylon 6. If you still have no idea what Nylon 6.6 is, do a search on google. Adjustable blade degree with included degree adjusters (Shims) Increase/decrease blade angle by installing degree adjuster under the blades “+” on the right side = Increase angle = More Torque, Less Speed “-” on the right side = Decrease angle = Less Torque, More Speed Nylon Blades Specification Material Nylon 6.6 + Carbon Fiber (<20%) Length 23.5 inches Width (base) 5 inches Mounting 6mm bolts Weight (per blade) 166g, 6oz Rotor Feature Apollo Competitor's Pros – 20mm rotor thickness, 66% more compare to competitor's – Stronger Magnetic flux due to thicker rotor, and thus, more Power – Evenly spread magnets decrease magnetic drag – 6 balanced hole to reduce weight – Reduce forces required to start rotor due to less reciprocation mass – Brushless Permanent Magnet Alternator Cons – only 12mm in rotor thickness and thus weaker magnetic flux – Magnets are not evenly spread out (ie: screw at top) – No weight reduction = harder start up Rotor Specification Rotor Diameter 77mm Magnet Material Rare Earth Neodymium magnets Number of Magnets 12 Magnet Width (Rotor thickness) 20mm Weight 682g Body Specification Material Aluminum (with coating) Length 62 cm Tail Height 33 cm Tail surface Area 225 cm^2 Upgradable with 29" blades Yes Blades allowed 6 Hub Specification Pros – 140mm diameter, 10% larger than competitor's – High blade capacity, allow up to 6 to be installed – Covers the entire face plate to eliminate vortex Cons – 125mm in diameter – Only allows 3 blades to be installed – Does not cover face plate completely Material Aluminum (with coating) Diameter 140 mm Capacity 6 Blades Compatibility Air-X, 403, 303 Shaft Diameter for 17mm shaft Disc Thickness 23mm II. Anti-Vibration System Horizontal Apollo Competitor's Pros – Dual Metal ball bearing located at front and rear of rotor – 5.5cm of stabilizing distance to prevent rotor and blades from vibrating – No vibration = Increase in efficiency – Reduction in noise output Cons – 2 bearings placed side by side together – Stabilizing distance effectively shorten to 2cm (63% reduction) – Vibration = Energy wasted – Wasted energy gets converted to Noise and Heat Vertical Apollo Competitor's Pros – Dual Metal ball bearing to prevent vertical vibration – Yaw shaft diameter: 40mm – 3cm of stabilizing distance with 2 bearings – No vibration = Increase in efficiency – Reduction in noise output – One piece design Yaw body provides more stability Cons – Single bearings will not eliminate vertical vibration – Yaw shaft diameter: 35mm – Stabilizing distance effectively shorten to 1.4cm with one bearing (53% reduction) – Vibration will cause bearing to grind on yaw shaft and create a bigger play, which in turn will cause more vibration in a never ending cycle – 2 pieces design Yaw body is less stable III. Anti-Leak System Apollo Competitor's Pros – Unlike rubber, PVC Rings are much more durable will not harden and crack and cause leaks – Bearing are covered and will not rust / leak Cons – Rubber ring will harden after approximately 1 year of use and will start cracking and leaking – Bearing are exposed and will rust / leak IV. Generator Specification Body Material Aluminum Rotor Diameter 124.5cm (49 inches) Starting Wind Speed 3.5m/s (8 mph) Rated Wind Speed 13m/s Survival Wind Speed 45m/s Voltage 12 V DC Rated Power 450W Maximum Power 550W Weight 7.88kg (17.39 lb) Yaw Body / Tower Mount Inner Diameter 53.3mm, 2.1 inch Recommended Tower (Pipe) Size 1.5 inch schedule 40 pipe Actual Pipe diameter: 48mm (1.9 inch) Recommend adding 2.5mm padding What are included: -1 Apollo Wind Turbine – 3x Blades – Hub with 6 lots – Nose Cone – Screws and Nuts – Degree Adjuster – Allen Key – Instruction Manual Apollo 650W 12V-24V AC ( 6 Blades ) Wind Turbine for Land or Marine Use Product designed in Canada I. Performance Slip Ring For those who are serious about wind power generation, this is a must have item. Never again will the cable get twisted up. Never again will you have to climb up the ladder and fix the tangles. Get a slip ring today and you can put all of that behind you. Slip Ring Specification: Circuits 3 Voltage 380VAC/DC Maximum Current 60A X3 Rated Current 40A X3 Working Speed 250RPM Temperature -40'C to 100'C Wire Gauge 6AWG Number of bearings 2 Thread M22x1.5 22mm diameter 1.5mm Thread Pitch Features: – High voltage / current carrying capacity – Copper-graphite brushes ensure long life even under extreme load conditions – Quick connector for fast connection to the AC / DC wind turbine *see reference picture below* – Insulated with fiberglass sleeves to protect wires to the wind turbine and make the installation professional and tidy – Easily taken apart for quick maintenance – 2x High Quality Metal Sealed Ball bearing to stabilize axle Exploded View Connection Overview As we can see from the exploded view, the top circuit is color coded Red, the middle circuit is Black and the bottom circuit is Blue. Curves The above battery charging power curve is obtained from charging a 12V 100Ah battery bank with our SolarWind Hybrid Charge Controller (not included in this listing) II. Anti-Vibration System [Same as above] III. Anti-Leak System [Same as above] IV. Generator Specification Body Material Aluminum Rotor Diameter 124.5cm (49 inches) Starting Wind Speed (6 blades) 3.0m/s (7 mph) Rated Wind Speed 13m/s Survival Wind Speed 45m/s Voltage 12 V-24V AC Rated Power 550W Maximum Power 650W Weight 8.28kg (18.25 lb) Yaw Body / Tower Mount Inner Diameter 53.3mm, 2.1 inch Recommended Tower (Pipe) Size 1.5 inch schedule 40 pipe Actual Pipe diameter: 48mm (1.9 inch) Recommend adding 2.5mm padding What are included: -1 Apollo Wind Turbine – 6x Blades – Hub with 6 lots – Nose Cone – Screws and Nuts – Degree Adjuster – Allen Key – Instruction Manual Apollo 800W 12V-24V AC (6 Blades) Wind Turbine for Land or Marine Use Product designed in Canada I. Performance Curves The above battery charging power curve is obtained from charging a 12V 100Ah battery bank with our SolarWind Hybrid Charge Controller. (not included in this listing) II. Anti-Vibration System [Same as above] III. Anti-Leak System [Same as above] IV. Generator Specification Body Material Aluminum Rotor Diameter 152.4cm (60 inches) Starting Wind Speed 3.0m/s (7 mph) Rated Wind Speed 13m/s Survival Wind Speed 45m/s Voltage 12 V-24V AC Rated Power 700W Maximum Power 800W Weight 8.8kg (19.4 lb) Yaw Body / Tower Mount Inner Diameter 53.3mm, 2.1 inch Recommended Tower (Pipe) Size 1.5 inch schedule 40 pipe Actual Pipe diameter: 48mm (1.9 inch) Recommend adding 2.5mm padding What are included: Apollo 29" Extended Blades and Tail Extension included for the 800W Model -1 Apollo Wind Turbine – 6x Blades – Hub with 6 lots – Nose Cone – Screws and Nuts – Degree Adjuster – Allen Key – Instruction Manual Apollo 1000W 12V-24V AC ( 6 Blades ) Wind Turbine for Land or Marine Use Product designed in Canada I. Performance Curves The above battery charging power curve is obtained from charging a 12V 100Ah battery bank with our SolarWind Hybrid Charge Controller (not included in this listing) Blade Features – Color: White – With 60" swept area when mounted on a 5" Hub – Incorporates highly efficient, true airfoil – Quiet performance with minimal vibration – Can generate 1000 watts or more depending on PMA efficiency – Manufactured using a precision injection molding process that produces blades of exceptional consistency – Made with new thermoplastic to increase durability – Smoother and more durable than any blades you can find in the market – Adjustable blade degree with included degree adjusters / shims (see picture below) – High resistance to bending (over 150 degrees) Material Nylon 6.6 + Carbon Fiber (<20%) Length 29 inches Width (base) 6 inches Mounting 6mm bolts Weight (per blade) 340g, 12oz Rotor Specification Apollo Competitor's Pros – 30mm rotor thickness, 150% more compare to competitor's – Stronger Magnetic flux due to thicker rotor, and thus, more Power – Evenly spread magnets decrease magnetic drag – 6 balanced hole to reduce weight – Reduce forces required to start rotor due to less reciprocation mass – Brushless Permanent Magnet Alternator Cons – only 12mm in rotor thickness and thus weaker magnetic flux – Magnets are not evenly spread out (ie: screw at top) – No weight reduction = harder start up Body Specification Rotor Diameter 77mm Magnet Material Rare Earth Neodymium magnets Number of Magnets 12 Magnet Width (Rotor thickness) 30mm Weight 1.34kg Reference picture ONLY. Please refer to listing details on the actual model you are getting. – Bigger body allow fitting of a more powerful alternator than competitor's – Longer body and tail (62cm) allow the Apollo to face wind even if more blades are added while our competitor just spins round and round – High surface area tail, 33cm in height, 30% more surface area will let the turbine stay focus to incoming wind – Installation of 29" blades and capture 50% more wind is now possible II. Anti-Vibration System [Same as above] III. Anti-Leak System [Same as above] IV. Generator Specification Body Material Aluminum Rotor Diameter 152.4cm (60 inches) Starting Wind Speed 3.0m/s (7 mph) Rated Wind Speed 13m/s Survival Wind Speed 45m/s Voltage 12 V-24V AC Rated Power 900W Maximum Power 1000W Weight 9.3kg (20.5 lb) Yaw Body / Tower Mount Inner Diameter 53.3mm, 2.1 inch Recommended Tower (Pipe) Size 1.5 inch schedule 40 pipe Actual Pipe diameter: 48mm (1.9 inch) Recommend adding 2.5mm padding What are included: Apollo 29" Extended Blades and Tail Extension included for the 1000W Model -1 Apollo Wind Turbine – 6x Blades – Hub with 6 lots – Nose Cone – Screws and Nuts – Degree Adjuster – Allen Key – Instruction Manual Phoenix 400W 12V DC ( 3 Blades) Wind Turbine for Land or Marine Use Power curve: Performance curve of power output versus wind speed Since wind speed increases with height, increases to the tower height can mean enormous increases in the amount of electricity generated by a wind turbine. Body Material Aluminium Rotor Diameter 117cm (46 inches) Starting Wind Speed 3m/s (7 mph) Rated Wind Speed 12.5m/s Survival Wind Speed 45m/s Voltage 12 V DC Rated Power 300W Maximum Power 400W Weight 5kg Mount Not included Blade Specification: Material Carbon Fiber Length 58cm (23 inches) Width (base) 12cm (4.5 inches ) Weight (per blade) 210g Features: – Incorporates highly efficient, true airfoil – Manufactured using a precision injection molding process that produces blades of exceptional consistency Nose Cone Specification: Material Plastic Diameter 135 mm Height 90mm Mounting Locks on Hub Thickness 3mm Weight 80g Features: – Reduce wind resistance – Eliminates vortexes – Greater stability – Neighbor Friendly 12V Or 24V Wind Turbine charge controller WARNING !!! Rotating blades present the most serious mechanical hazard. The blades may be moving at velocities over 275 miles per hour (440 km/hr). At this speed, the tip of a blade is nearly invisible and can cause serious injury. Under no circumstances should you install the turbine where a person could come in contact with moving rotor blades. The installer of these blades is solely responsible for the use or misuse of these blades. We assume no liability for ANY injuries caused by these products. Warranty: We will warrant this unit against any manufacture defects or workmanship for 6 months from the date of purchase. This limited warranty specifically excludes damage caused by improper installation, accident, misuse, abuse, improper storage, or any unauthorized disassembly, repair, or modification.This warranty is not transferable. In the event of a claim against this warranty, the seller's obligation, and the claimant's sole remedy, shall be replacement of the product, repair, or refund of the original purchase price excluding any shipping and handling fees. All shipping and handling fees going both ways are responsible by the buyer. NO OPERATING COST GENERATES ELECTRICITY FROM THE ABUNDANT RESOURCE Terms & Conditions Bidding this auction means that you agree with the following terms & conditions. All pictures and descriptions are subjected to change without notice. Items may not look exactly the same as the auction shown. We are not responsible for any inadvertent errors. Payment Total payment = winning price + shipping & handling Insufficient payment will be charge extra US$0.50 to compensate the Paypal penalty fees. Shipping & Handling Total shipping = Base S&H + Combine S&H ( for each additional item ) a) Base S&H is the highest shipping cost of the first item. 1. Combine shipments are only available on the condition of a SINGLE PAYMENT. Auctions that are paid separately will NOT be shipped in combo and therefore, they are not qualified for shipping discounts. 2. We ship within 2 working days after payment is received and confirmed. Please allow up to 5-10 BUSINESS DAYS for item(s) with a physical address sending to the 48 states of United States & Canada. For international bidders, the shipping time varies with respect to your location. 3. Bounce backs due to incorrect shipping address will result in setback on deliveries. It is the buyer's responsibility to repay the shipping & handling fees. 4. We are not responsible for any loses or damages resulting from shipping. Return & Refund Policy No refunds after 30 days Shipping & handling & other service fees are NOT refundable All returned items must be in original packing. Items that are used/ damaged/ deformed or altered in any ways will not be accepted. A 20% restocking fee will be charged on all refunded items. E-mails E-mails are usually answered within 2~3 business days in priority order. Spams and mass e-mailing will be deleted without slightest glance. E-mails with virus or anything subjected to hacking are automatically deleted.

Outdoor Dimmer 650W String Light Dimmer Wireless RF Smart Plug-In Outdoor Dimmer

Outdoor Dimmer, 650W String Light Dimmer, Wireless RF Smart Plug-In Outdoor Dimmer Switch – Timer Function/IP65 Waterproof/50FT

Solar Optimizer SOLAREDGE MPPT 650W PV Optimizer Save Energy Power Optimizer

Product Description Solar Optimizer SOLAREDGE MPPT 650W PV Optimizer Save Energy Power OptimizerPower Optimizer Photovoltaic Optimizer 650w with PV to Enhance Performance Solar Optimizer Features:l Module level maximum power point tracking (MPPT) to improve power yield by 5-25%.l Real-time panel monitoring for timely warning and locating problemsl Safe solar system with remote shutdown to eliminate high voltage hazardsl Flexible system design to maximise space utilisation.l 25-year lifespan, perfectly matched solar modules Specification:l Output Power: 650Wl Output Current: 15Al Output Voltage Range: 0-75Vl MPPT Voltage Range: 12-75Vl Size: 152x133x25.9mm Package Includes:1x Power Optimizer About Us Payment Shipping Returns Contact Us We are a professional worldwide wholesale company, with our own factory located in China. We supply many products including Consumer Electronics, Home & Garden, Health & Beauty, Apple accessories, Computers accessories, Car accessories, Clothing accessories, Sports & Outdoor Accessories.Our principle: offer high quality product to worldwide at reasonable prices. Customers 100% satisfaction is our top priority. Payment should be done within 7 days after the end of the Auction. Otherwise Unpaid Item Dispute will be filed with eBay.eCheck payments take 3 to 7 business days to clear through PayPal.International Buyers Please Note: a) Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. b) Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying.Please list your special requests (color, packages, etc.) in the PAYPAL NOTES SECTION when you make payment. All items will be dispatched within Promise business day after full payment is received and verified. It normally takes 7-12 business days to United States. Delivery Time is about 15-25 business days to most of the other countries. It may take longer to other countries or remote areas. We are unable to take any responsibility for wrong address, any custom delay or tax. Transit time is highly depended and provided by Postal Service. If you have not received your shipment within 30 days from payment, please contact us. We will track the shipment and get back to you as soon as possible with a reply. We back our products with a 60-DAY Return GUARANTEE. Customers should inspect item(s) and notify us within 60 days of any problems. If you have a problem with your item, please contact us before leaving feedback. All items being returned must be issued an RMA number BEFORE they are returned. 6 months Warranty from the date of purchase covering manufacturing defects. This warranty excludes any damage caused by the user. Return shipping is to be paid by the Buyer. 100% Customer satisfaction is our top priority.Please give us a chance to make it right before leaving a neutral/negative feedback or opening disputes.Business hours of operation:Monday – Friday: 9:00 AM – 6:00 PM Standard Beijing Time.Saturday, Sunday and all Public Holidays: Closed. About Us We are a professional worldwide wholesale company, with our own factory located in China. We supply many products including Consumer Electronics, Home & Garden, Health & Beauty, Apple accessories, Computers accessories, Car accessories, Clothing accessories, Sports & Outdoor Accessories.Our principle: offer high quality product to worldwide at reasonable prices. Customers 100% satisfaction is our top priority. Payment Payment should be done within 7 days after the end of the Auction. Otherwise Unpaid Item Dispute will be filed with eBay.eCheck payments take 3 to 7 business days to clear through PayPal.International Buyers Please Note: a) Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. b) Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying.Please list your special requests (color, packages, etc.) in the PAYPAL NOTES SECTION when you make payment. Shipping All items will be dispatched within Promise business day after full payment is received and verified. It normally takes 7-12 business days to United States. Delivery Time is about 15-25 business days to most of the other countries. It may take longer to other countries or remote areas. We are unable to take any responsibility for wrong address, any custom delay or tax. Transit time is highly depended and provided by Postal Service. If you have not received your shipment within 30 days from payment, please contact us. We will track the shipment and get back to you as soon as possible with a reply. Returns We back our products with a 60-DAY Return GUARANTEE. Customers should inspect item(s) and notify us within 60 days of any problems. If you have a problem with your item, please contact us before leaving feedback. All items being returned must be issued an RMA number BEFORE they are returned. 6 months Warranty from the date of purchase covering manufacturing defects. This warranty excludes any damage caused by the user. Return shipping is to be paid by the Buyer. Contact Us 100% Customer satisfaction is our top priority.Please give us a chance to make it right before leaving a neutral/negative feedback or opening disputes.Business hours of operation:Monday – Friday: 9:00 AM – 6:00 PM Standard Beijing Time.Saturday, Sunday and all Public Holidays: Closed. powered by

4-pack IronRidge FM-SQ-BHW-V2 Square Bolt Bonding Hardware NEW

Brand: IronRidge Description: 4-pack, square bolt bonding hardware Please note for size reference, each square in the picture is one inch. Part Number: FM-SQ-BHW-V2 Condition: NEW, bag has handling. Shipping will be calculated based zip code. Seller can change shipping method at their discretion, for faster and more reliable service. However, if you chose priority mail it will be shipped with fastest service. Please ask any questions before bidding, and thanks for looking. (Loc: LL-1) All reasonable Best Offers will be considered! Please view the pictures. What is included in this listing is in the picture. If you don’t see it, it’s not included, unless specifically mentioned in the listing description. If you have questions, feel free to ask! Please note, items may not come in the original box if the box is not in shipping condition. I do show the label when available so you can see the part number. Payment: You have 3 days to pay, or send payment for items. Non paying bidders will be reported to ebay. This costs sellers time and money. Shipping: For items $50 and up, shipping insurance is included in the shipping cost for US customers only. Please note: Parcel Post can take a long time! Especially to the East Coast. If you need your item fast, use Ground or Priority mail! INTERNATIONAL AND CANADA! USPS First Class Mail CAN take over a month!!! If you need it fast choose USPS PRIORITY!!! All items are shipped in a timely fashion (1-2 business days). Please provide a correct shipping address through Paypal, and for ground shipments please provide a telephone number as most ground shipments are shipped via FedEx Ground. Returns: Items are guaranteed to work on arrival, unless otherwise stated in the auction. If there is a significant cause for return, notify me within 3 days of receiving the item. Shipping is not refunded, so PLEASE make sure that you are purchasing the correct item for your needs! Do not threaten me with feedback before you have even contacted me. That is not a great way to start communications, and as you can see from my feedback, I always try to work with my customers. By bidding on this item you are agreeing to the terms of the above disclaimer. (120320)r

4-pack IronRidge FM-SQ-BHW-V2 Square Bolt Bonding Hardware NEW

IronRidge CTR-TR84-01-B1 Contour Trip 84 Inch

Stellavolta.com is an authorized dealer and we only sell new products. Review this product’s handling time by clicking on the “Shipping and Payments” tab above. Ships primarily via USPS, however, we may ship UPS Ground or FedEx Ground. Faster shipping options available. We accept PayPal and all major credit cards. IronRidge CTR-TR84-01-B1 Contour Trip 84 Inch IronRidge Contour™ Trim elevates the look of any solar array by providing a sleek trim (or skirt) across the south edge or around the perimeter to hide components that are visible beneath the solar panels. Homeowners want the solar on their home to meet their energy needs, while not detracting from their home’s aesthetics. Contour™ will make any array look great, and have your crew on and off the roof in a snap. Exchanges or Returns Please contact us before returning or exchanging an item to receive a return authorization (RA). Items returned to us without receiving a return authorization will be returned to you at your expense. We accept exchanges and returns for unopened items or damaged/defective products within 30 days of receipt of shipment. A 20% restocking fee may apply to multiple quantity returns or large ticket items. A 20% restocking fee will apply for all products that ship freight. Exchanges and returns are not accepted after 30 days of receipt of shipment. Unopened Products To make an exchange or return for an unopened product, please contact us and obtain a Return Authorization. If the exchanged or returned product is unopened with all original accessories, manuals, packaging, and/or shrink wrap, you will be responsible for return shipping. If the product was sold with free shipping, shipping charges to deliver the item will be deducted from the refund amount. A refund to your method of payment will be processed within one week of receiving an authorized return minus any applicable shipping charges. Damaged/Defective Products To make an exchange or return for a damaged/defective product, please contact us and obtain a Return Authorization. If the product is returned for being damaged/defective, we will provide a return shipping label for domestic shipping costs. If we test and confirm the product is damaged/defective and receive the product along with all original accessories, manuals, and packing, we will provide a refund for the purchase price of the product, plus domestic shipping charges, if any, assessed at the time of purchase. International shipping charges, if any, will not be reimbursed. A refund to your method of payment will be processed within one week of receiving an authorized return. If we test and confirm the product is in full working order, a refund will not be provided and you will be responsible for providing a return shipping label to have the product returned to you.

Item Tag: Buyer